07552 597814 Radstock & Bath's Trusted Gate Maker

Services

Gates & Metalwork in Radstock

Bespoke driveway gates, automated entrances, pedestrian gates, railings and ironwork, designed from scratch and built in the workshop near Radstock.

Bespoke Driveway Gates in Radstock

Steel driveway gates measured, designed and welded to fit your opening, your boundary and the slope of your drive.

What's included

  • Design worked up from sketches or photos
  • Steel gates welded and finished in the workshop
  • Measured on site before fabrication starts
  • Hung and set to swing or slide correctly
  • Sloping and angled openings worked out properly
  • Painted or powder-coated finish

Every gate starts with the opening as it actually is, not a standard size off a catalogue. I go out to measure, look at how the ground falls, check what the gate needs to clear and talk through the style, straight bars, solid infill, estate pattern, whatever suits the house. From there I draw it up so you can see what you're getting before any steel is cut.

Once the design's agreed, the gate is built in the workshop and brought out for hanging. Posts are set properly to take the weight, hinges are sized for the gate, and everything is checked for swing and clearance before I leave. Finish is either painted or powder-coated depending on what you want and how the gate will be used.

Bespoke Driveway Gates in Radstock

Gate Automation in Radstock

Electric gate motors, control gear and safety sensors fitted to new or existing gates, including on sloping or angled drives.

What's included

  • Motors sized to the gate's weight and length
  • Wiring and control boxes installed and tested
  • Safety edges and photocells fitted
  • Keypads, fobs or phone-app entry set up
  • Sloping and uneven ground accounted for in the design
  • Existing gates assessed for automation

Automating a gate is as much about the ground and the gate itself as it is the motor. I look at how steep or uneven the drive is, how heavy the gate will be, and where power and controls can run before recommending a system, rather than fitting a standard kit and hoping it copes.

For a full entrance, main gate, pedestrian gate and automation together, I plan the whole layout so the electrics, hinges and motor positions all work as one job rather than being bolted on afterwards. Once installed, everything is tested for safe operation, including the safety edges and sensors that stop the gate if something's in the way.

Gate Automation in Radstock

Pedestrian Gates in Radstock

Matching pedestrian gates made to sit alongside a main driveway gate or stand alone at a side or garden entrance.

What's included

  • Designed to match an existing or new driveway gate
  • Made to the width and height of your opening
  • Hinges and latch fitted to suit the gate's use
  • Painted or powder-coated to match
  • Fitted square and level, checked for swing
  • Can be built as part of a wider gate scheme

A pedestrian gate is usually part of a bigger picture, sitting next to a main gate, matching its style and finish, or covering a side access that needs its own entry. I design it alongside the main gate where there is one, so the two read as a single scheme rather than two separate jobs.

Fitting is the same care as any gate: opening measured accurately, posts set to take the weight, hinges and latch sized for daily use, and the gate checked for a clean swing before I finish up.

Pedestrian Gates in Radstock

Metal Railings in Radstock

Steel and iron railings welded and fitted along driveways, paths, boundary walls and gardens.

What's included

  • Railings measured and designed to your boundary
  • Steel or iron bar sections welded in the workshop
  • Fixed to walls, kerbs or set in the ground
  • Matched to gates or other metalwork on site
  • Painted or powder-coated finish
  • Straight runs or railings that follow a slope

Railings get the same treatment as a gate, measured on site, designed to fit the actual run rather than a standard panel width, and made to follow the ground where it isn't flat. If you're also having a gate made, I can design the railings to match so the whole boundary reads as one job.

Fixing depends on what they're going into, bolted to a wall or kerb, or set into the ground, and I work out the right method on site before anything's welded up, so the finished railing is solid and doesn't move.

Metal Railings in Radstock

Garden Gate Restoration in Radstock

Rusted, sagging or damaged garden gates repaired, straightened and repainted rather than replaced.

What's included

  • Gate assessed for what can be saved
  • Rusted or damaged sections cut out and replaced
  • Frame straightened and hinges reset
  • Rust treated before repainting
  • Repainted or powder-coated to finish
  • Refitted and rehung to swing properly

Not every tired gate needs replacing. I'll look at what's actually wrong, rust through a section, a dropped hinge, a frame that's twisted out of square, and work out what can be cut out and repaired against what needs a full rebuild. Old ironwork is often worth saving if the bones are sound.

Repair work is done back in the workshop where I can weld in new steel cleanly, treat any rust properly before it's repainted, and reset the hinges so the gate hangs and swings the way it should once it's back in place.

Garden Gate Restoration in Radstock

Decorative Ironwork in Radstock

One-off ironwork, panels, balustrades and ornamental pieces, hand-forged and welded to a design worked out with you.

What's included

  • Designed around your idea, sketch or reference
  • Hand-forged and welded panels and details
  • Balustrades and ornamental panels
  • Made to fit an existing opening or space
  • Painted or powder-coated finish
  • One-off pieces, not standard patterns

Decorative work starts the same way as a gate, a conversation about what you're after, whether that's a scrolled panel, a balustrade with some detail in it, or a standalone ornamental piece. I sketch up options so you know what's being made before it's forged.

Because each piece is one-off, everything is hand-worked to the design rather than pulled from stock patterns. It's then finished and fitted to whatever space or fixing it's going into, whether that's a wall, staircase or garden feature.

Decorative Ironwork in Radstock

How It Works

Three steps, no pressure

1

Call or message Jacob

Tell me what you're after, a photo of the opening or a rough sketch is enough to start with. I'll ask what I need to know, or arrange to come and see it if it's a more complex site.

2

Free quote

I'll measure up, talk through the design and any tricky ground or angles, and give you a detailed, honest quote, no pressure, no obligation to go ahead.

3

The work

Once you're happy, I build the gate or ironwork in the workshop, then come out to fit it, set it up properly and make sure it's swinging or operating exactly as it should before I leave.

Get In Touch

Book Your Free Survey

Get in touch with Jacob for a free site survey and a fixed, no-obligation quote.

Call Now WhatsApp Quote