Services
Chimney Services in Arlington
Sweeping, inspections, repairs and cap work, done properly and explained in plain terms so you know your fireplace is safe to use.
Chimney Sweeping in Arlington
Soot and creosote cleared from the flue with drop cloths down and the work area protected throughout.
What's included
- Full flue brush and vacuum
- Firebox and smoke shelf cleared
- Creosote buildup removed
- Drop cloths down, carpets protected
- Debris bagged and hauled away
I brush and vacuum the full length of the flue to clear soot and creosote, then clean out the firebox and smoke shelf where debris tends to collect unseen. Everything that comes down gets bagged and taken with me, not left in a pile by the hearth.
Before I start I lay drop cloths from the fireplace to the door so nothing tracks through the house. Most sweeps take a single visit, and I'll tell you on the spot if I find anything during the clean that needs a closer look.

Chimney Inspections in Arlington
A full check of the flue, crown, cap and liner before problems turn into repairs.
What's included
- Flue liner checked for cracks
- Crown and cap condition assessed
- Flashing and mortar joints checked
- Screening checked for gaps
- Firebox and damper tested
- Written findings explained on site
I go over the whole system, not just what's visible from the hearth: the crown, the cap, the flashing where the chimney meets the roof, and the liner itself for cracks or wear. Missing or damaged screening is one of the most common things I find, since it lets leaves, birds, and debris straight into the flue.
Once I'm done I walk you through exactly what I found, in plain language, before recommending anything. If a repair is needed I'll explain why, and if it isn't, I'll tell you that too.

Chimney Repairs in Arlington
Cracked crowns, damaged flashing and worn mortar joints fixed and explained before I start.
What's included
- Cracked or spalled crowns repaired
- Flashing resealed or replaced
- Mortar joints repointed
- Damaged flue liners addressed
- Damper repair or adjustment
Most of the repairs I do trace back to water getting in somewhere it shouldn't: a cracked crown, failed flashing, or mortar joints that have started to break down. I fix the cause, not just the symptom, so the same problem doesn't come back in a year.
I explain what's wrong and what the fix involves before I start work, and I come back to finish the job properly if it can't be done in one visit.

Chimney Cap Installation in Arlington
A cap fitted to the top of the flue to keep rain, debris and animals out for good.
What's included
- Cap sized and fitted to the flue
- Existing damaged caps removed
- Cap secured against wind and weather
- Multi-flue caps for more than one flue
A missing or broken cap is one of the most common things I find during an inspection, and it's usually the reason rain, leaves, or birds have been getting into the chimney. I fit a cap sized correctly to your flue and secure it so it stays put in wind and weather.
If there's an old cap in place already, I'll remove it and replace it rather than fitting a new one over the top. Once it's on, the flue is sealed off from anything trying to get in from above.

Flue Screening & Protection in Arlington
Screening fitted and repaired so leaves, birds and debris can't get back into the chimney.
What's included
- Screening fitted to the flue opening
- Damaged or missing mesh replaced
- Gaps checked and sealed
- Screening checked as part of every inspection
Screening is the simple fix that stops most of the debris problems I see in Arlington chimneys. Gaps or missing mesh let leaves and nesting birds straight down the flue, where they build up and block airflow over time.
I fit or repair screening as its own job or alongside a sweep and cap installation, and I check it as a matter of course on every inspection so it doesn't get overlooked again.

Fireplace Maintenance Advice in Arlington
A plain-language walkthrough of what to watch for between visits, so problems get caught early.
What's included
- What to check between sweeps
- Signs of creosote buildup to watch for
- When to schedule your next inspection
- How to spot cap or screening damage
At the end of every visit I take a few minutes to explain what I found and what to keep an eye on before I'm back out again. That might be how quickly creosote builds up with regular use, or what a damaged cap looks like from the ground.
It's not a sales pitch, it's the same plain-terms explanation I give with every sweep or repair, just focused on keeping the fireplace safe between visits rather than fixing something in the moment.

How It Works
Three steps, no pressure
1
Call or message
Tell Maxwell what's going on with the chimney or fireplace. He'll ask enough questions to know whether he needs to come look at it himself.
2
Free survey & quote
He comes out, inspects the chimney properly, and gives you a fixed quote before any work starts.
3
The work
Maxwell does the sweep, repair or install, protects the house while he's at it, and explains what he found before he leaves.